NVT210DMTR2G【PDF 16/20 页】IC TEMP SENSOR DGTL 8-WDFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录46

12页 13页 14页 15页 [16页]17页 18页 19页 20页

NVT210

http://onsemi.com

Figure 20. Operation of the THERM

and THERM2

Interrupts

THERM2

LIMIT

905C

805C

705C

605C

505C

405C

TEMPERATURE

THERM

305C

THERM

LIMIT

THERM2

?SPAN class="pst NVT210DMTR2G_2295433_6"> When the THERM2

limit is exceeded, the THERM2

signal asserts low.

?SPAN class="pst NVT210DMTR2G_2295433_6"> If the temperature continues to increase and exceeds the

THERM

limit, the THERM

output asserts low.

?SPAN class="pst NVT210DMTR2G_2295433_6"> The THERM

output deasserts (goes high) when the

temperature falls to THERM

limit minus hysteresis. In

Figure 20, there is no hysteresis value shown.

?SPAN class="pst NVT210DMTR2G_2295433_6"> As the system cools further, and the temperature falls

below the THERM2

limit, the THERM2

signal resets.

Again, no hysteresis value is shown for THERM2

Both the external and internal temperature measurements

cause THERM

and THERM2

to operate as described.

Application Information

Noise Filtering

For temperature sensors operating in noisy environments,

the industry standard practice was to place a capacitor across

the D+ and D pins to help combat the effects of noise.

However, large capacitances affect the accuracy of the

temperature measurement, leading to a recommended

maximum capacitor value of 1,000 pF. Although this

capacitor reduces the noise, it does not eliminate it, making

it difficult to use the sensor in a very noisy environment.

The NVT210 has a major advantage over other devices

when it comes to eliminating the effects of noise on the

external sensor. The series resistance cancellation feature

allows a filter to be constructed between the external

temperature sensor and the part. The effect of any filter

resistance seen in series with the remote sensor is

automatically cancelled from the temperature result.

The construction of a filter allows the NVT210 and the

remote temperature sensor to operate in noisy environments.

Figure 21 shows a low-pass R-C-R filter, where R = 100 W

and C = 1 nF. This filtering reduces both common-mode and

differential noise.

Figure 21. Filter between Remote Sensor and

NVT210 Factors Affecting Diode Accuracy

100 W

1 nF

D+

REMOTE

TEMPERATURE

SENSOR

Remote Sensing Diode

The NVT210 is designed to work with discrete transistors.

Substrate transistors are generally PNP types with the

collector connected to the substrate. Discrete types are either

PNP or NPN transistors connected as diodes (base-shorted

to collector). If an NPN transistor is used, the collector and

base are connected to D+ and the emitter to D. If a PNP

transistor is used, the collector and base are connected to D

and the emitter to D+.

To reduce the error due to variations in discrete transistors,

consider several factors:

?SPAN class="pst NVT210DMTR2G_2295433_6"> The ideality factor, nF, of the transistor is a measure of

the deviation of the thermal diode from ideal behavior.

The NVT210 is trimmed for an nF value of 1.008. The

following equation may be used to calculate the error

introduced at a temperature, T (癈), when using a

transistor whose nF does not equal 1.008. Consult the

processor data sheet for the nF values.

DT = (nF 1.008)/1.008 ?(273.15 Kelvin + T)

To factor this in, the user writes the DT value to the offset

from, the temperature measurement.

If a discrete transistor is used with the NVT210, the best

accuracy is obtained by choosing devices according to the

following criteria:

?SPAN class="pst NVT210DMTR2G_2295433_6"> Base-emitter voltage greater than 0.25 V at 6 mA, at the

highest operating temperature

?SPAN class="pst NVT210DMTR2G_2295433_6"> Base-emitter voltage less than 0.95 V at 100 mA, at the

lowest operating temperature

?SPAN class="pst NVT210DMTR2G_2295433_6"> Base resistance less than 100 W

?SPAN class="pst NVT210DMTR2G_2295433_6"> Small variation in h

(50 to 150) that indicates tight

control of V

characteristics

Transistors, such as the 2N3904, 2N3906, or equivalents

in SOT23 packages are suitable devices to use.

Thermal Inertia and Self-heating

Accuracy depends on the temperature of the remote

sensing diode and/or the internal temperature sensor being

at the same temperature as that being measured. Many

factors can affect this. Ideally, place the sensor in good

thermal contact with the part of the system being measured.

If it is not, the thermal inertia caused by the sensors mass

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式